2 %\documentclass[doublespacing]{elsart}
3 \documentclass[]{elsart}
4 %\usepackage[activate]{pdfcprot}
8 \usepackage[english]{babel}
9 \usepackage[latin1]{inputenc}
10 \usepackage[T1]{fontenc}
15 \usepackage[dvips]{graphicx}
22 \selectlanguage{english}
28 \title{Molecular dynamics simulation of defect formation and precipitation
29 in heavily carbon doped silicon}
31 \author[augsburg]{F. Zirkelbach\corauthref{cor}}
32 \author[augsburg]{J. K. N. Lindner}
33 \author[helsinki]{K. Nordlund}
34 \author[augsburg]{B. Stritzker}
36 \address[augsburg]{Experimentalphysik IV, Institut f\"ur Physik,
37 Universit\"at Augsburg,\\
38 Universit\"atsstr. 1, D-86135 Augsburg, Germany}
39 \address[helsinki]{Accelerator Laboratory, Department of Physical Sciences,
40 University of Helsinki,\\
41 Pietari Kalmink. 2, 00014 Helsinki, Finland}
43 \corauth[cor]{Corresponding author.\\
44 Tel.: +49-821-5983008; fax: +49-821-5983425.\\
45 E-mail address: frank.zirkelbach@physik.uni-augsburg.de
49 The precipitation process of silicon carbide in heavily carbon doped silicon is not yet fully understood.
50 High resolution transmission electron microscopy observations suggest that in a first step carbon atoms form C-Si dumbbells on regular Si lattice sites which agglomerate into large clusters.
51 In a second step, when the cluster size reaches a radius of a few nm, the high interfacial energy due to the SiC/Si lattice misfit of almost 20\% is overcome and the precipitation occurs.
52 By simulation, details of the precipitation process can be obtained on the atomic level.
53 A newly parametrized Tersoff-like bond order potential is used to model the system appropriately.
54 First results gained by molecular dynamics simulations using this potential are presented.
58 Silicon, carbon, silicon carbide, nucleation, defect formation,
59 molecular dynamics simulations
64 \section{Introduction}
65 Understanding the precipitation process of cubic silicon carbide (3C-SiC) in heavily carbon doped silicon will enable significant technological progress in thin film formation of the important wide band gap semiconductor material SiC \cite{1}.
66 On the other hand it will likewise offer perspectives for processes which rely upon prevention of precipitation events, e.g. the fabrication of strained, pseudomorphic $\text{Si}_{1-y}\text{C}_y$ heterostructures \cite{2}.
68 Epitaxial growth of 3C-SiC films is achieved either by ion beam synthesis (IBS) \cite{3}, chemical vapour deposition (CVD) or molecular beam epitaxy (MBE) techniques.
69 While in CVD and MBE surface effects need to be taken into account, SiC formation during IBS takes place in the bulk of the Si crystal.
70 In the present work the simulation assumes conditions similar to those of the ion implantation process.
72 First of all a picture of the supposed precipitation event is presented.
73 Then the applied simulation sequences are introduced.
74 Finally first simulation results are presented.
76 \section{Supposed Si to 3C-SiC conversion mechanism}
77 Crystalline silicon (c-Si) has diamond structure and thus is composed of two fcc lattices which are displaced by one quarter of the volume diagonal.
78 3C-SiC grows in zincblende structure, i.e. is also composed of two fcc lattices one out of which is occupied by Si and the other by C atoms.
79 The length of four lattice constants of c-Si is approximately equal to the length of five 3C-SiC lattice constants ($4a_{\text{Si}}\approx 5a_{\text{3C-SiC}}$) resulting in a lattice misfit of almost 20\%.
80 Due to this the silicon atomic density of 3C-SiC is slightly lower than the one of c-Si.
82 There is a supposed conversion mechanism of heavily carbon doped c-Si into 3C-SiC \cite{4}.
83 As concluded from high resolution transmission electron microscopy (HREM) carbon atoms introduced into c-Si form C-Si dumbbells on regular Si lattice sites.
84 The dumbbells agglomerate into large clusters, called embryos.
85 Finally, when the cluster size reaches a critical radius of 2 to 4 nm, the high interfacial energy due to the 3C-SiC/c-Si lattice misfit is overcome and precipitation occurs.
86 In HREM this transformation manifests itself by the disappearance of patches with dark background in favour of high resolution Moir\'e fringes due to 3C-SiC precipitates embedded in c-Si \cite{3,4}.
87 Due to the slightly lower silicon density of 3C-SiC excessive silicon atoms exist which will most probably end up as self-interstitials in the c-Si matrix since there is more space than in 3C-SiC.
89 Thus, in addition to the precipitation event itself, knowledge of C and Si interstitials in Si are of great interest in order to investigate the precipitation of 3C-SiC in heavily C doped c-Si.
91 \section{Simulation sequences}
92 A molecular dynamics simulation approach is used to examine the steps involved in the precipitation process.
93 For integrating the equations of motion the velocity verlet algorithm \cite{5} with a timestep of 1 fs is adopted.
94 The interaction of the silicon and carbon atoms is realized by a newly parametrized Tersoff-like bond order potential \cite{6}.
95 Since temperature and pressure of the system is kept constant in experiment the isothermal-isobaric NPT ensemble is chosen for the simulation.
96 Coupling to the heat bath is achieved by the Berendsen thermostat \cite{7} with a time constant of 100 fs.
97 The pressure is controlled by the Berendsen barostat \cite{7} again using a time constant of 100 fs and a bulk modulus of 100 GPa for silicon.
98 To exclude surface effects periodic boundary conditions are applied.
99 In order to study the behaviour of carbon in c-Si, two different simulation sequences are used.
101 To investigate the interstitial configurations of C and Si atoms in c-Si, a simulation volume of $9\times9\times9$ silicon unit cells is used.
102 The temperature is set to 0 K.
103 In separated simulation runs a carbon or a silicon atom is inserted in the central unit cell at the tetrahedral (0,0,0) (${\color{red}\triangleleft}$), a hexagonal (-1/8,-1/8,1/8) (${\color{green}\triangleright}$), a nearly dumbbell (-1/8,-1/8,-1/4) (${\color{magenta}\Box}$) or at a random position (in units of the silicon lattice constant) where the origin is located in the centre of the unit cell (Fig. 1).
104 In order to avoid too high potential energies in the case of the dumbbell configuration the nearest silicon neighbour atom is manually shifted to (-3/8,-3/8,-1/4) ($\circ$).
105 The energy introduced into the system by the insertion of atoms is scaled out within a relaxation phase of 2 ps.
107 For the simulations aiming to reproduce a precipitation process the simulation volume is 31 silicon lattice constants in each direction.
108 The system temperature is set to $450\, ^{\circ} \textrm{C}$ like in IBS \cite{3}.
109 $6000$ carbon atoms (the number necessary to form a 3C-SiC precipitate with a radius of $\sim 3$ nm) are consecutively inserted in a way to keep the system temperature constant.
110 Carbon is inserted statistically distributed over either the whole simulation volume (insertion volume $V_1$), an insertion volume $V_2$ corresponding to the minimum size of a 3C-SiC precipitate or the volume $V_3$ containing the number of Si atoms necessary for the formation of such a minimum precipitate.
111 The two latter insertion volumes are considered since no diffusion of carbon atoms is observed at this temperature.
112 Following the insertion procedure the system is cooled down to $20\, ^{\circ} \textrm{C}$.
115 The insertion of individual Si atoms leads to stable tetrahedral and <110> dumbbell self-interstitial configurations as observed earlier in \cite{6}.
116 The formation energies are 3.4 eV and 4.4 eV, respectively.
117 However, the hexagonal dumbbell configuration is not stable opposed to results in \cite{6}.
118 The Si interstitial atom moves towards an energetically more favorable position very close to the tetrahedral one but slightly displaced along the three coordinate axes.
119 The formation energy of 4.0 eV for this type of interstitials equals the result obtained in \cite{6} for the hexagonal one.
120 The same type of interstitial arises using random insertions.
121 In addition, variations exist in which the displacement is only along two <100> axes ($E_f=3.8\, \text{eV}$) or along a single <100> axis ($E_f=3.6\, \text{eV}$) succesively approximating the tetrahedral configuration and formation energy.
123 In carbon insertion simulations the tetrahedral and <110> dumbbell carbon interstitial configurations are observed to be stable.
124 The formation energies are 2.7 eV and 1.8 eV, respectively.
125 Again, the hexagonal configuration is found to be unstable.
126 The carbon interstitial atom moves to the more favorable <100> dumbbell position which has a formation energy of 0.5 eV.
127 This interstitial configuration is shown in Fig. 2.
128 There is experimental evidence \cite{8} of the existence of this configuration.
129 It is frequently generated and has the lowest formation energy of all the defects observed in all the simulation runs in which carbon is inserted at random positions.
130 Fig. 3 schematically displays the <100> dumbbell configuration including the atomic displacements relative to the atoms initial positions together with resulting new Si-Si and C-Si pair distances.
132 Fig. 4 shows resulting pair correlation functions of the simulation runs targeting the observation of precipitation events.
133 The contributions of Si-C and C-C pairs are presented separately.
134 The three curves represent results for the insertion of 6000 C atoms into the three different volumes $V_1$, $V_2$ and $V_3$, as explained above.
135 There is no significant difference between carbon insertions into $V_2$ and $V_3$.
137 The number of C-C bonds for $V_1$ is much smaller than for $V_2$ and $V_3$ since carbon atoms are spread over the total simulation volume, which means that there is only 0.2 carbon atoms per silicon unit cell on average.
138 The first C-C peak appears at about 0.15 nm.
139 This is comparable to the nearest neighbour distance of graphite or diamond.
140 It is assumed that these carbon atoms form strong C-C bonds which is supported by a decrease of the total energy during carbon insertion for the $V_2$ and $V_3$ in contrast to the $V_1$ simulation.
142 The C-C peak at $\sim 0.31$ nm perfectly matches the distance of two carbon atoms in the 3C-SiC lattice. In 3C-SiC the same distance is also expected for Si-Si bonds.
143 The Si-Si portion of the pair correlation function for the case of 3000 C atoms inserted into $V_2$ is displayed in Fig. 5, together with a reference function for pure c-Si.
144 After insertion of C atoms the Si-Si pair correlation function in fact shows non-zero g(r) values around distance values of 0.31 nm while the amount of Si pairs at the regular distances of 0.24 and 0.38 nm decreases.
145 However, no clear peak is observed but the interval of enhanced g(r) values corresponds to the width of the C-C g(r) peak.
146 Analyses of randomly chosen configurations in which distances around 0.3 nm appear, identify <100> C-Si dumbbells to be responsible for stretching the Si-Si next neighbour distance for low C concentrations, i.e. for the $V_1$ and early stages of $V_2$ and $V_3$ simulation runs.
147 This excellently agrees with the calculation for a single <100> dumbbell (r(13) in Fig. 3).
148 For higher C concentrations the defect concentration is likewise increased and a considerable amount of damage is introduced into the insertion volume.
149 Damage and superposition of defects generate new displacement arrangements which become hard to categorize and trace and obviously lead to a broader distribution of pair distances.
150 The step-like increase of Si-Si pairs at 0.29 nm is probably due to the Si-Si cut-off radius of 0.296 nm in the used bond order potential \cite{6}.
151 The cut-off function causes artificial forces pushing the Si atoms out of the cut-off region.
152 By visualizing the C-C atom pairs with distances of 0.31 nm, concatenated, differently oriented <100> dumbbell interstitials are frequently observed.
153 This leads to the assumption that C atoms introduced in that way are the first elements arranged at distances expected for 3C-SiC which at a later stage pull the Si atoms into the right configuration.
155 The Si-C pair correlation (Fig. 4) shows the formation of Si-C atom pairs displaced approximately by 0.187 nm.
156 This corresponds quite well to the expected next neighbour distance of 0.189 nm for Si and C atoms in 3C-SiC.
157 For low concentrations again <100> dumbbell configurations can be identified to contribute to this pair distance (r(3C) in Fig. 3).
158 Further more, the bump at 0.175 (r(1C) in Fig. 3) and the peaks at about 0.333, 0.374, 0.386, 0.431 and 0.464 nm are comprehensible by comparing with calculated values in Fig. 3 and the dashed vertical lines in Fig. 4.
159 The dashed lines mark further calculated C-Si atom pair distances appearing in the <100> C-Si dumbbell interstitial configuration which are not displayed in Fig. 3.
160 The distinct peak at 0.26 nm, which exactly matches the cut-off radius of Si-C interaction, is again a potential artefact.
161 For high carbon concentrations again superposition of defects and high amounts of damage characterize the pair distances.
162 Short range order indeed is observed but only hardly visible is the long range order.
163 This suggests to use higher temperatures particularly with regard to $V_2$ and $V_3$ simulations, i.e. simulations with high carbon concentrations, so that the system is able to get over an energy barrier escaping a local minimum configuration.
164 An increase of the simulation temperature should not be in conflict with experimental conditions since the target temperature of $450\, ^{\circ} \textrm{C}$ measured during the IBS of 3C-SiC \cite{3} at the substrat holder is most certainly lower than the temperature predominating near the target surface, where 3C-SiC formation takes place.
167 The conversion of heavily C doped c-Si into 3C-SiC precipitates is investigated.
168 Molecular dynamics simulation sequences to analyze interstitial configurations and the precipitation of 3C-SiC are introduced.
169 The <100> C-Si dumbbel reproduced by simulation is observed the energetically most favorable configuration and explained in detail.
170 First results of the simulations suggest that in the precipitation process C atoms introduced as differently oriented C-Si dumbbells into the c-Si matrix are the first elements properly arranged for the 3C-SiC formation.
171 Furthermore, the observation of high amounts of damage particularly for high carbon concentrations demands for elevated system temperatures to achieve the precipitation event.
173 \begin{thebibliography}{8}
174 \bibitem{1} J. H. Edgar, J. Mater. Res. 7 (1992) 235.
175 \bibitem{2} J. W. Strane, S. R. Lee, H. J. Stein, S. T. Picraux,
176 J. K. Watanabe, J. W. Mayer, J. Appl. Phys. 79 (1996) 637.
177 \bibitem{3} J. K. N. Lindner, Appl. Phys. A 77 (2003) 27.
178 \bibitem{4} P. Werner, R. Koegler, W. Skorupa, and D. Eichler:
179 in Proc. 11th Int. Conf. on Ion Implantation Technology,
180 ed. by E. Ishidida, S. Banerjee, S. Mehta, T. C. Smith,
181 M. Current, L. Larson, A. Tasch, T. Romig
182 (Austin, TX, USA, June 16-21, 1996) pp. 675
183 \bibitem{5} L. Verlet, Phys. Rev. 159 (1967) 98.
184 \bibitem{6} P. Erhart and K. Albe, Phys. Rev. B 71 (2005) 35211.
185 \bibitem{7} H. J. C. Berendsen, J. P. M. Postma, W. F. van Gunsteren,
186 A. DiNola, J. R. Haak, J. Chem. Phys. 81 (1984) 3684.
187 \bibitem{8} G. D. Watkins and K. L. Brower, Phys. Rev. Lett. 36 (1976) 1329.
188 \end{thebibliography}
195 \includegraphics[width=8cm]{fig1.eps}
196 \caption{Insertion positions for the tetrahedral (${\color{red}\triangleleft}$), hexagonal (${\color{green}\triangleright}$) and <110> dumbbell (${\color{magenta}\Box}$) interstitial configuration.}
202 \includegraphics[width=6cm]{fig2.eps}
203 \caption{Position of a <100> dumbbell carbon interstitial in silicon.
204 Only bonds of the carbon interstitial atom are shown.}
210 \includegraphics[width=15cm]{fig3.eps}
211 \caption{Schematic of the <100> C-Si dumbbell configuration.
212 Displacements of the atoms relative to their initial position are given.
213 The displacement of the carbon atom is relative to the initial position of atom 1.
214 New resulting Si-Si and C-Si pair distances r(ij) for the atoms (ij) shown in the schematic are recorded.}
220 \includegraphics[]{fig4.eps}
221 \caption{Pair correlation functions for Si-C and C-C bonds.
222 The three curves represent results for the three different insertion volumes $V_1$, $V_2$ and $V_3$, as explained in the text.
223 The dashed vertical lines mark further calculated C-Si atom pair distances appearing in the <100> C-Si dumbbell interstitial configuration, which are not displayed in Fig. 3.}
229 \includegraphics[]{fig5.eps}
230 \caption{Si-Si pair correlation function for pure Si and Si with 3000 inserted C atoms.
231 The inset shows a magnified region between 0.28 and 0.36 nm.}