+\caption{Free energy and temperature evolution of plain silicon at temperatures in the region around the melting transition.}
+\label{fig:md:fe_and_t}
+\end{figure}
+
+\subsection{Long time scale simulations at maximum temperature}
+
+As discussed in section~\ref{subsection:md:limit} and~\ref{subsection:md:inct} a further increase of the system temperature might help to overcome limitations of the short range potential and accelerate the dynamics involved in structural evolution.
+Furthermore these results indicate that increased temperatures are necessary to drive the system out of equilibrium enabling conditions needed for the formation of a metastable cubic polytype of SiC.
+
+A maximum temperature to avoid melting is determined in section \ref{subsection:md:tval} to be 120 \% of the Si melting point but due to defects lowering the transition point a maximum temperature of 95 \% of the Si melting temperature is considered usefull.
+This value is almost equal to the temperature of $2050\,^{\circ}\mathrm{C}$ already used in former simulations.
+Since the maximum temperature is reached the approach is reduced to the application of longer time scales.
+This is considered usefull since the estimated evolution of quality in the absence of the cooling down sequence in figure~\ref{fig:md:tot_si-c_q} predicts an increase in quality and, thus, structural evolution is liekyl to occur if the simulation is proceeded at maximum temperature.
+
+Next to the employment of longer time scales and a maximum temperature a few more changes are applied.
+In the following simulations the system volume, the amount of C atoms inserted and the shape of the insertion volume are modified from the values used in first MD simulations.
+To speed up the simulation the initial simulation volume is reduced to 21 Si unit cells in each direction and 5500 inserted C atoms in either the whole volume or in a sphere with a radius of 3 nm corresponding to the size of a precipitate consisting of 5500 C atoms.
+The 100 ps sequence after C insertion intended for structural evolution is exchanged by a 10 ns sequence, which is hoped to result in the occurence of infrequent processes and a subsequent phase transition.
+The return to lower temperatures is considered seperately.
+
+\begin{figure}[!t]
+\begin{center}
+\includegraphics[width=12cm]{c_in_si_95_v1_si-c.ps}\\
+\includegraphics[width=12cm]{c_in_si_95_v1_c-c.ps}
+\end{center}
+\caption{Si-C (top) and C-C (bottom) radial distribution for low concentration simulations at 95 \% of the potential's Si melting point at different points in time of the simulation.}
+\label{fig:md:95_long_time_v1}
+\end{figure}
+\begin{figure}[!t]
+\begin{center}
+\includegraphics[width=12cm]{c_in_si_95_v2.ps}
+\end{center}
+\caption{Si-C and C-C radial distribution for high concentration simulations at 95 \% of the potential's Si melting point at different points in time of the simulation.}
+\label{fig:md:95_long_time_v2}
+\end{figure}
+
+Figure \ref{fig:md:95_long_time_v1} shows the evolution in time of the radial distribution for Si-C and C-C pairs for a low C concentration simulation.
+Differences are observed for both types of atom pairs indeed indicating proceeding structural changes even well beyond 100 ps of simulation time.
+Peaks attributed to the existence of substitutional C increase and become more distinct.
+However, no increase of the amount of total C-C pairs within the observed region can be identified.
+Carbon, whether substitutional or as a dumbbell does not agglomerate within the simulated period of time.
+
+Figure \ref{fig:md:95_long_time_v2} shows the evolution in time of the radial distribution for Si-C and C-C pairs for a high C concentration simulation.
+There are only small changes identifiable.
+Explain more ...
+
+For both, high and low concentration simulations the radial distribution converges as can be seen by the nearly identical graphs for the last two points in time.
+Changes exist ... bridge to results after cooling down to 20 degree C.
+
+{\color{red}Todo: Cooling down to 20 degree C and compare.}
+
+{\color{red}Todo: Remember NVE simulations (prevent melting).}
+
+\subsection{Further accelerated dynamics approaches}